A simple rerate can added 15, 25, 50, or even 100... Increase Your Cat Diesel Engine Horsepower. Repair the wiring between the sensor and the ECM. An undersized radiator may cause the engine to run at a temperature that is higher than normal. C. Check operation of the pressure relief valve and/or the water temperature regulator. Refer to the Systems Operation/Testing and Adjusting manual. Illustration 1 g01150024 Repair the leak. coolant is not present at the sensor probe, J1/P1:49 D. Verify that one of the following diagnostic codes (coolant level normal) has an output of near 0 VDC. Result The radiator has internal blockage. Free shipping on many items | Browse your favorite brands ... OEM CAT SENSOR GP-SP 2454630. The normal temperature is dependent on the ambient temperature. For further assistance, your TC can confer with the Dealer Solutions Network (DSN). The coolant level sensor monitors the engine coolant level in order to warn the operator when the coolant level is low. Clean the components and/or replace the components. Make sure that the drive gear is not loose on the drive shaft of the coolant pump. OEM CAT BUST PRESS SENSOR 2935534. C. Measure the voltage between terminals A (sensor supply) and B (sensor return) at the harness connector for the coolant level sensor. C13, C15, and C18 Engines Troubleshooting – Coolant Level Is Low, C13, C15, and C18 Engines Troubleshooting – Cooling Fan Is Always ON. Check that the seating surfaces of the pressure relief valve and the radiator cap are clean and undamaged. Cat sensors detect liquid levels at specific locations. Add coolant according to the procedure in the Operation and Maintenance Manual. Doesn't seem to be any power to the air module for the fan. Ensure that the radiator size is sufficient. Check the NRS cooler for leaks. Result: The “Coolant Level Sensor” parameter is not programmed correctly. ... Prev C13, C15, and C18 Engines Troubleshooting – Coolant Level Is Low. Troubleshoot the circuit and the coolant temperature sensor. Illustration 3 g02090761 Make the necessary repairs. Your email address will not be published. E. Remove the jumper wire. (1) Coolant temperature sensor. (09-06-2018, 07:08 PM) Rjpierma24 Wrote: Where is the CGI temp sensor located on a 2010 cat c13. Engine Coolant Temperature High – Most Severe (3), Water Temperature Regulator and/or Pressure Relief Valve. 3406E and 3456 Industrial Engines Testing and Adjusting – Cooling System – Test, 3406E and 3456 Industrial Engines Testing and Adjusting – Cooling System – Inspect, 3406E and 3456 Industrial Engines Testing and Adjusting – Cooling System – Check – Overheating, 3406E and 3456 Industrial Engines Testing and Adjusting – Increased Engine Oil Temperature – Inspect, 3406E and 3456 Industrial Engines Testing and Adjusting – Excessive Engine Oil Consumption – Inspect, The voltage is within ±5 VDC of battery voltage. Integrated Cat … A. Cat low temperature sensors use thermocouples and thermistors to sense temperature. Wait at least 30 seconds for activation of the status indicator. The coolant level sensor configuration parameter must be set to “Installed” in order for the ECM to monitor the signal from the sensor. Verify that the repair eliminates the problem. Check for collapsed hoses and/or other restrictions. The activation of an event code and/or a warning lamp is probably caused by a low coolant level. The CAT part # is 228-4800. west_coaster, Mar 28, 2017. west_coaster, Mar 28, 2017 #1 + Quote Reply. Cat C15 ACERT engines are the ideal solution for your demanding operations in the oilfield. This video goes into detail how to remove and install Cat twin turbo IVA and VVA solenoids. Result The fan clutch is not operating correctly. Required fields are marked *. Your email address will not be published. The next likely cause is a problem with the wiring harness, a connector, or the sensor. ABOUT THIS PRODUCT. A.Remove the cylinder head.